Answer evaluation · interactive demo

A marked answer sheet, question by question.

A sample Class 12 Physics answer sheet, marked against its scheme. Tap a red mark to see why it was given or held back.

Interactive demo · sample content written by Angira · results are pre-written

Answer evaluation is in development and has not been validated against independent teacher marking.

Read the question paper (sample, board-style)

Angira board-practice paper · Physics · Class 12 · Sample section (board-style, written by Angira) · Maximum marks for this section: 13

  1. A small, strong bar magnet is released from rest at the top of a long vertical copper tube and falls along the axis of the tube without touching its walls. An unmagnetised iron bar of the same size and mass, released in the same way, reaches the bottom much sooner. Explain why. Neglect air resistance. [2]
  2. A 3 µF capacitor is charged to 120 V by a battery. The battery is then removed and the capacitor is connected across an uncharged 6 µF capacitor. Find (i) the common potential of the two capacitors, and (ii) the electrostatic energy lost in the process. [3]
  3. Using Gauss’s law, obtain an expression for the electric field at a distance r from an infinitely long, thin, straight wire carrying a uniform linear charge density λ. Draw the Gaussian surface you use and state the direction of the field. [3]
  4. (a) Draw a labelled ray diagram showing how a refracting astronomical telescope forms the image of a distant object in normal adjustment. [2] (b) Define the magnifying power of the telescope and write its expression in normal adjustment. [1] (c) The objective and the eyepiece of such a telescope have focal lengths 150 cm and 5 cm. Find its magnifying power in normal adjustment and the separation between the two lenses. [1] (d) Give one reason why the objective of a telescope is made with a large aperture. [1] [5]

Sample report

Marked answer sheet

Score 10.5/13

Sample answer sheet written for this demo, shown in a handwriting-style font. Red marks are the report’s; tap one to see it in Mark details.

Sample student · DEMO-0001Page 1 of 3
  1. Ans 1.
  2. As the magnet falls through the copper tube, the mag. flux linked
  3. with the walls of the tube (think of it as many rings) keeps changing.
  4. ∴ by Faraday’s law an emf is induced in the walls & since Cu is a ✓
  5. good conductor, eddy currents (circular) flow in the walls. ✓
  6. By Lenz’s law these currents oppose the cause producing them,
  7. i.e. the relative motion b/w magnet & tube. So they exert an
  8. upward (retarding) force on the magnet. ✓
  9. ∴ net downward force < mg ⇒ a < g, so it takes more time.
  10. Unmagnetised iron bar → no flux change → no eddy currents → falls with a = g. ✓2
  11. Ans 2. Given: C₁ = 3 µF, V₁ = 120 V, C₂ = 6 µF (uncharged)
  12. (i) After connecting, charge is conserved.
  13. q = C₁V₁ = 3 × 10⁻⁶ × 120 = 360 × 10⁻⁶ C = 360 µC
  14. Common potential V = q / (C₁ + C₂) = 360 µC / 9 µF ✓
  15. = 30 V × Common potential 30 V incorrect; 0.5 deducted.
  16. (ii) Initial energy Uᵢ = ½ C₁V₁²
  17. = ½ × 3 × 10⁻⁶ × (120)² = ½ × 3 × 10⁻⁶ × 14400
  18. = 0.0216 J ✓
  19. Final energy Uf = ½ (C₁ + C₂) V²
  20. = ½ × 9 × 10⁻⁶ × (30)² = ½ × 9 × 10⁻⁶ × 900
  21. = 4.05 × 10⁻³ J ✓ P.T.O.
Sample student · DEMO-0001Page 2 of 3
  1. Energy lost = Uᵢ − Uf = 0.0216 − 0.00405 ✓
  2. = 0.01755 J
  3. ∴ Energy lost ≈ 0.0176 J (lost as heat in connecting wires)2.5
  4. Ans 3.
  5. ++++ λrEl Gaussian surface End faces: zero flux not stated. 0.5 deducted.
  6. Consider a cylindrical Gaussian surface of radius r & length l, coaxial with the wire. ✓
  7. ∮ E·dA = E × 4πr²
  8. By symmetry E is radial & has the same magnitude at all pts on the curved surface.
  9. ∴ Flux through curved surface φ = E × 2πrl ✓
  10. Charge enclosed q = λl ✓
  11. By Gauss’s law, φ = q / ε₀
  12. E × 2πrl = λl / ε₀
  13. ⇒ E = λ / (2πε₀r)
  14. directed radially outward (if λ is +ve). ✓2.5
Sample student · DEMO-0001Page 3 of 3
  1. Ans 4. (a) Astronomical telescope — normal adjustment3.5
  2. IF₀, Fₑβα f₀fₑ ObjectiveEyepiece ✓ ✓ ! Review flag ✓
  3. (b) Magnifying power is the ratio of the angle subtended at the eye by the
  4. final image to the angle subtended at the eye by the object (seen directly). ✓
  5. m = β / α = f₀ / fₑ ✓
  6. (c) f₀ = 150 cm, fₑ = 5 cm
  7. m = f₀ / fₑ = 150 / 5 = 30 ✓
  8. Length of tube L = f₀ + fₑ = 150 + 5 = 155 Separation given without unit; 0.5 deducted.
  9. (d) Part (d): no answer. 1 mark not awarded.

Mark details

Question Q1 · summary

Question Q1: 2 / 2 FULL

Page 1, lines 2-10: changing flux in the tube wall (Faraday’s law), eddy currents in the copper, Lenz’s law with an upward retarding force, a < g, and the comparison with the iron bar (no flux change, a = g) are all stated..

AI scoring confidence · 93%

The AI’s estimate of certainty for this question. Accuracy against independent marking has not yet been established.

Missed value points

No value points were missed.

Show marking scheme demo addition

The report does not show scheme rows; this sample’s scheme is here so you can check each mark.

  1. ✓ awardedThe magnetic flux linked with the tube wall changes as the magnet falls, so an emf is induced (Faraday’s law)½
  2. ✓ awardedEddy (circulating) currents flow in the conducting copper wall½
  3. ✓ awardedBy Lenz’s law the currents oppose the relative motion, giving an upward (retarding) force on the magnet½
  4. ✓ awardedNet force < mg, so acceleration < g; the iron bar has no changing flux and falls with g½

Question Q2 · summary

Question Q2: 2.5 / 3 PARTIAL

360 uC / 9 uF = 40 V; the value 30 V on page 1, line 16 is an arithmetic error, 0.5 deducted.

AI scoring confidence · 88%

The AI’s estimate of certainty for this question. Accuracy against independent marking has not yet been established.

Missed value points

Common potential: 40 V required; 30 V written (page 1, line 16).

Necessary explanation

360 uC / 9 uF = 40 V; the value 30 V on page 1, line 16 is an arithmetic error, 0.5 deducted. U_f = 4.05 x 10^-3 J (page 1, line 22) and energy lost = 0.01755 J (page 2, line 2) are correct for V = 30 V and are not deducted again (error carried forward). For V = 40 V, U_f = 7.2 x 10^-3 J and energy lost = 1.44 x 10^-2 J.

Show marking scheme demo addition

The report does not show scheme rows; this sample’s scheme is here so you can check each mark.

  1. ✓ awardedCharge conservation: q = C1V1 = 360 µC and V = q/(C1 + C2)½
  2. × not awardedV = 40 V½
  3. ✓ awardedUi = ½C1V1² = 2.16 × 10⁻² J½
  4. ✓ awardedUf = ½(C1 + C2)V² = 7.2 × 10⁻³ J (error carried forward allowed)½
  5. ✓ awardedEnergy lost = Ui − Uf½
  6. ✓ awardedEnergy lost = 1.44 × 10⁻² J, with unit (error carried forward allowed)½

Question Q3 · summary

Question Q3: 2.5 / 3 PARTIAL

Page 2 contains no statement about the flat end faces; Figure 3 shows field arrows on the curved surface only.

AI scoring confidence · 84%

The AI’s estimate of certainty for this question. Accuracy against independent marking has not yet been established.

Missed value points

Zero flux through the two flat end faces of the cylinder (E perpendicular to their area vectors) is not stated.

Necessary explanation

Page 2 contains no statement about the flat end faces; Figure 3 shows field arrows on the curved surface only. The rubric requires the statement: 0.5 deducted. The struck-through line on page 2, line 13 (E x 4*pi*r^2) was not assessed.

Show marking scheme demo addition

The report does not show scheme rows; this sample’s scheme is here so you can check each mark.

  1. ✓ awardedGaussian surface: a cylinder of radius r and length l, coaxial with the wire, shown in a figure½
  2. × not awardedFlux through the two flat end faces is zero (E perpendicular to their area vectors)½
  3. ✓ awardedE radial and of the same magnitude on the curved surface; flux there = E × 2πrl½
  4. ✓ awardedCharge enclosed q = λl½
  5. ✓ awardedE × 2πrl = λl/ε0, giving E = λ/(2πε0r)½
  6. ✓ awardedDirection: radially outward for λ > 0½

Question Q4 · summary

Question Q4: 3.5 / 5 BEST ESTIMATE UNCERTAIN

Part (c), page 3, line 16: L = 155 written without a unit; 0.5 deducted.

AI scoring confidence · 58%

The AI’s estimate of certainty for this question. Accuracy against independent marking has not yet been established.

Missed value points

Part (c): separation stated as 155 without a unit. Part (d): no reason given for the large objective aperture.

Necessary explanation

Part (c), page 3, line 16: L = 155 written without a unit; 0.5 deducted. Part (d): only the label "(d)" appears on page 3, line 17; no assessable answer to part (d) was found on any of the 3 pages; 1 mark not awarded. Part (b): m = f0/fe is accepted for m = -f0/fe.

Best-estimate mark included

Figure 4, page 3: the three rays leaving the eyepiece spread slightly towards the eye. Normal adjustment requires parallel emergent rays. The intermediate image is drawn at the common focus, the heading reads "normal adjustment", and the middle ray is parallel to the dashed line through the eyepiece centre. The 0.5 mark for parallel emergent rays is included as a best estimate.

Show marking scheme demo addition

The report does not show scheme rows; this sample’s scheme is here so you can check each mark.

  1. ✓ awarded(a) Parallel incident rays meet in the objective’s focal plane: real, inverted intermediate image½
  2. ✓ awarded(a) Intermediate image at the eyepiece’s focus; separation f0 + fe shown½
  3. ! best estimate(a) Rays leaving the eyepiece drawn parallel (final image at infinity)½
  4. ✓ awarded(a) Labels: objective, eyepiece, f0, fe, α and β; arrows on rays½
  5. ✓ awarded(b) Definition: angle subtended by the final image ÷ angle subtended by the object½
  6. ✓ awarded(b) m = −f0/fe in normal adjustment (magnitude accepted)½
  7. ✓ awarded(c) m = 150/5 = 30½
  8. × not awarded(c) L = f0 + fe = 155 cm, with unit½
  9. × not awarded(d) One reason: more light gathered, or higher resolving power1

What this demo shows

The report follows Angira’s answer evaluation: marks on the student’s own pages, with the reason, AI confidence and any review flag behind each one. Angira wrote the paper, the sheet and every mark; nothing calls an AI model. It is in internal testing. See where it stands.